What’s actually slowing this PC down?
Pick the symptom - the matching free tool is one click away.
Some links on this page are affiliate links: if you buy through them we may earn a commission, at no extra cost to you.
Choosing a magnesium alloy for a lightweight structural part starts with the manufacturing route and product form—not with a generic strength ranking. For wrought sheet, plate, extrusion, or structural sections, AZ31B is a common starting point; for complex high-volume die castings, AZ91D is widely used. Parts needing more elongation and impact tolerance may favor AM-series die-casting grades, while elevated-temperature and creep demands can point toward AS41B or AE42. The defensible choice depends on the exact load case, temperature history, corrosion interfaces, alloy condition, specification, and certification basis.
What should you decide before comparing magnesium grades?
Fix the production route and product form first. A sheet alloy, an extrusion alloy, and a die-casting alloy are not interchangeable simply because their designations all contain magnesium, aluminum, zinc, or manganese. Product form, temper, section thickness, heat treatment, and test method can change the usable properties as much as the alloy name.
As an Amazon Associate I earn from qualifying purchases.
Define whether the part will be made by warm-forming sheet or plate, extrusion, forging, die casting, permanent-mold or sand casting, or machining from certified stock. The U.S. military technical order describes AZ31B as a material for sheet, plate, extrusions, and structural sections, while die-casting guidance identifies AZ91D as a widely used casting grade. The government technical order and NADCA’s magnesium guidance are useful starting references.
Also define the business context before narrowing the grade. Prototype quantities may favor machining or a simple formed blank, whereas a large production run can justify a die and the tooling amortization that comes with it. A low material price can be overwhelmed by scrap, finishing, inspection, or special handling. Conversely, a more expensive alloy may reduce assembly count or machining enough to lower the delivered part cost. Put these assumptions in the material-selection record so that a later supplier quotation does not silently change the design basis.
Popular on Amazon
- 【90 Degree Full Function USB C Adapter】Supports the latest USB4 standard for up to 40Gbps of bandwidth, 8K video support, and up to 240W Fast charging; Support USB PD 3.1 Extended Power Range (EPR) including 140W, 180W and 240W. Your productivity is easily doubled. *Warm Tip: For the best fit, please make sure the USB-C port is fully exposed; thick or bulky cases may affect compatibility.
- 【Reliable Quality】Made from high-quality, scratch-resistant aluminum alloy, delicate metal frame. get excellent wear resistance and heat dissipation. Non-Slip Design for easier insertion and removal.
- 【Small and portable】Ultra thin size, ultra compact design, a petite physique that matches the minimalist design of your modern laptops. Coming with a slim figure that won't block the port next to the one it's plugged into.
- 【Compatibility】Widely work with most usb c, thunderbolt 4/3 devices. Compatibilit for ROG Ally, Steam Deck, Switch, MacBook Pro, Quest 3 VR headset, Surface Book 2, iPhone 18/17/16/15, Samsung Galaxy S23/S22/S21, Note 20/10, Google Pixel, ChromeBook, etc.
- 【Excellence Customer Support】If you experience any issues or cable failure, simply reach out to our dedicated customer service team. We provide a prompt response within 18 hours, providing you with the necessary technical support to resolve any concerns.
How do you translate the load case into alloy requirements?
Write the structural requirement as a set of failure modes rather than a single tensile-strength target. Record tensile and compressive loads, bending, buckling, fatigue cycles, impact or energy absorption, allowable deflection, joining loads, and required elongation. Then identify the controlling property for each mode.
- Static strength: compare yield and ultimate values for the actual form, temper, orientation, and thickness.
- Stiffness: magnesium’s low density is valuable, but elastic modulus is much lower than that of steel; size the section for deflection and buckling, not just mass.
- Fatigue: use allowables for the surface condition, stress concentration, mean stress, environment, and manufacturing route.
- Impact: prioritize elongation, fracture behavior, and energy absorption over headline strength when crash or drop loading governs.
- Joining: include fastener bearing, weld or adhesive qualification, galvanic isolation, and local heat effects.
For thin panels and beams, calculate the mass at the required stiffness rather than comparing density in isolation. A magnesium section may need more depth, ribs, or local reinforcement to meet deflection and buckling limits. Those geometric changes can affect die fill, bend radii, machining time, and the area that needs corrosion protection.
Quick wins for a faster PC:
Repair Windows errors before they cause bigger problemsFix Now →Fix the driver behind crashes, sound loss and screen glitchesFind Drivers →Clear out junk files and repair common Windows errorsFree Scan →Do not turn typical catalogue numbers into design allowables. MMPDS-2024 explains that mechanical properties depend on sampling location, specimen type, test method, and procurement specification. NADCA likewise notes that its die-casting values come from separately cast test specimens rather than production castings. Obtain the governing specification and the allowable-data basis before releasing a design.
Which magnesium alloys are sensible first candidates?
| Candidate and route | Shortlist when | Main tradeoff or verification |
|---|---|---|
| AZ31B wrought sheet, plate, extrusion, structural section | Lightweight formed or machined structures using wrought product | Confirm product specification, temper, forming route, orientation, and design values; AZ31B-H24 sheet and plate are covered by an SAE material specification example. |
| AZ91D die casting | Complex castings where high commercial strength and good castability are required | Typical as-cast values are from separate specimens; control iron, copper, and nickel impurities for corrosion performance. |
| AM60B, AM50A, or AM20 die casting | Elongation, toughness, and impact tolerance are more important than maximum strength | Lower aluminum content generally increases ductility but reduces strength and castability. |
| AS41B or AE42 die casting | Elevated-temperature strength and creep resistance are key concerns | Use time- and temperature-dependent data for the actual exposure; the family name does not establish a permissible service temperature. |
| AZ61A, WE43, or ZK60A wrought grades | Higher-performance or aerospace-oriented wrought comparisons are justified and supply is available | Verify the required condition, specification, environmental data, and allowables; listing in MMPDS is not proof of fit. |
NADCA calls AZ91D “the most widely-used magnesium die casting alloy.” Its 2021 table gives typical separately cast values of 230 MPa tensile strength, 160 MPa yield strength, and 3% elongation for AZ91D. The same table gives AM60B typical values of 220 MPa tensile strength, 130 MPa yield strength, and 6–8% elongation. These figures are useful for understanding the strength–ductility tradeoff, not for substituting for a design allowable.
NADCA lists nominal AZ91D chemistry as 9.0% aluminum, 0.7% zinc, and 0.2% manganese. Actual purchase requirements must use the applicable chemistry limits and certification documents.
The density figures also need context. NADCA cites approximately 1.74 g/cm³ for magnesium and lists 1.76–1.81 g/cm³ for the seven die-casting alloys in its table. Differences within that range are usually less important than section sizing, porosity, ribs, inserts, and finishing. A lighter grade is not automatically the lightest finished assembly.
When is AZ31B the right starting point?
Start with AZ31B when the geometry is naturally a wrought product: bent sheet, plate, extrusion, or a structural section that can be machined after forming. Its availability in several product forms can simplify sourcing and joining compared with developing a custom casting. The government technical order specifically identifies these AZ31B forms.
Also popular on Amazon
- 5-in-1 Connectivity: Equipped with a 4K HDMI port, a 5 Gbps USB-C data port, two 5 Gbps USB-A ports, and a USB C 100W PD-IN port. Note: The USB C 100W PD-IN port supports only charging and does not support data transfer devices such as headphones or speakers.
- Powerful Pass-Through Charging: Supports up to 85W pass-through charging so you can power up your laptop while you use the hub. Note: Pass-through charging requires a charger (not included). Note: To achieve full power for iPad, we recommend using a 45W wall charger.
- Transfer Files in Seconds: Move files to and from your laptop at speeds of up to 5 Gbps via the USB-C and USB-A data ports. Note: The USB C 5Gbps Data port does not support video output.
- HD Display: Connect to the HDMI port to stream or mirror content to an external monitor in resolutions of up to 4K@30Hz. Note: The USB-C ports do not support video output.
- What You Get: Anker 332 USB-C Hub (5-in-1), welcome guide, our worry-free 18-month warranty, and friendly customer service.
Room-temperature forming is constrained by magnesium’s hexagonal close-packed crystal structure. Warm or hot forming may be needed for bends, deep draws, or complex profiles. Establish forming temperature, lubrication, minimum bend radius, springback, and post-forming heat treatment with the processor; do not assume an aluminum-style cold-forming process will transfer directly.
For a formed part, identify rolling or extrusion direction and put the principal stresses in the favorable orientation when the specification permits. Check thinning at bends, edge cracking, residual stress, and dimensional change after trimming. A forming trial on a representative blank is more informative than a flat tensile coupon if the design contains tight radii or multiple draw operations.
For procurement, specify alloy, product form, temper, thickness or section dimensions, applicable material specification, chemistry certification, mechanical tests, inspection, and traceability. SAE’s topic index displayed AMS4377K for AZ31B-H24 sheet and plate as current on June 17, 2025; verify the live revision and project applicability before placing an order. Do not assume that a supplier’s generic “AZ31B sheet” description identifies H24 temper, thickness range, or certification level.
The Tool Desk
Outbyte PC Repair FREEClear out junk files and repair common Windows errorsFree Scan →Outbyte Driver Updater FREEFix the driver behind crashes, sound loss and screen glitchesFind Drivers →When should a die-casting grade replace a wrought grade?
Choose die casting when the part has complex ribs, bosses, thin walls, integrated mounting features, and production volume sufficient to justify tooling. Casting can reduce assembly and machining, but properties vary with wall thickness, porosity, cooling rate, location, and heat treatment. Design critical sections and inspection around those realities.
AZ91D is a practical high-strength, widely available die-casting benchmark. If the part must absorb impact or tolerate deformation before fracture, compare AM60B, AM50A, and AM20. NADCA describes AM-series grades as favoring elongation, toughness, and impact resistance, generally at the expense of strength and castability as aluminum content is reduced.
Use the casting simulation and process plan to check thin-wall filling, hot spots, vents, gates, ejector locations, and expected shrinkage. Keep highly loaded bosses away from predictable porosity zones where possible, and specify machining stock so that a critical surface is not opened into a defect. If heat treatment is required, include distortion, dimensional inspection, and the effect on corrosion behavior in the qualification plan.
For a casting, request data tied to the actual casting process and critical locations. A separately cast coupon can overstate or understate production performance, so acceptance criteria should address porosity, section size, heat treatment, and inspection method. If the design depends on a local property, test coupons cut from production-representative regions or qualify the complete part.
Recommended Free Tools
Also popular on Amazon
- Sleek 7-in-1 USB-C Hub: Features an HDMI port, two USB-A 3.0 ports, and a USB-C data port, each providing 5Gbps transfer speeds. It also includes a USB-C PD input port for charging up to 100W and dual SD and TF card slots, all in a compact design.
- Flawless 4K@60Hz Video with HDMI: Delivers exceptional clarity and smoothness with its 4K@60Hz HDMI port, making it ideal for high-definition presentations and entertainment. (Note: Only the HDMI port supports video projection; the USB-C port is for data transfer only.)
- Double Up on Efficiency: The two USB-A 3.0 ports and a USB-C port support a fast 5Gbps data rate, significantly boosting your transfer speeds and improving productivity.
- Fast and Reliable 85W Charging: Offers high-capacity, speedy charging for laptops up to 85W, so you spend less time tethered to an outlet and more time being productive.
- What You Get: Anker USB-C Hub (7-in-1), welcome guide, 18-month warranty, and our friendly customer service.
How should elevated temperature and creep change the shortlist?
Separate room-temperature strength from long-duration performance. A part that is strong in a short tensile test can lose load capacity through creep, stress relaxation, or microstructural changes during sustained exposure to heat.
For cast components with elevated-temperature or creep demands, investigate AS41B and AE42 first, then compare their data with the actual temperature-time-stress history. MMPDS-2024 also lists cast grades including EV31A, QE22A, EZ33A, and ZE41A. Their inclusion in a reference manual only identifies them as documented grades; it does not establish suitability for your temperature, environment, geometry, or life.
Specify a maximum continuous and intermittent temperature, dwell duration, duty cycle, preload, and allowable deformation. Use creep curves or time-dependent allowables at the design temperature, with knockdowns for casting quality and surface condition where required. Include thermal expansion mismatch with inserts, bolts, coatings, and neighboring parts; repeated thermal cycles can loosen joints or damage a protective finish even when the average stress is acceptable.
How do corrosion and galvanic interfaces affect the choice?
Evaluate the complete assembly, not an isolated coupon. Moisture, salt, contaminants, coating damage, trapped water, and dissimilar-metal fasteners can dominate service life.
NADCA attributes AZ91D’s corrosion performance partly to strict limits on iron, copper, and nickel impurities. Sanwa’s processing guidance warns that contact with iron, stainless steel, or copper can accelerate corrosion on the magnesium side through galvanic action. Mitigations include compatible coatings, insulating sheets, isolation washers or sleeves, sealed joints, drainage, and controlled fastener finishes. Sanwa’s corrosion and processing overview describes these isolation measures.
Define the environment (humidity, salt spray, chemicals, temperature), coating system, edge and fastener protection, inspection interval, and repair method. If electrical continuity is required, design a deliberate bonding path rather than allowing random metal-to-metal contact. Validate the assembled joint, because a coating that protects flat panels may fail at a cut edge, threaded hole, or fretting interface.
Specify how the part will be cleaned and dried, where water can drain, and how damaged coating will be repaired in service. Isolation washers and sleeves must survive bolt preload, vibration, wear, and temperature; a soft isolator that creeps may eventually expose the galvanic couple. Consider sealants and joint geometry together, since a sealed crevice that traps electrolyte can be worse than a deliberately drained joint.
Also popular on Amazon
- Portable and powerful USB-C HUB: BENFEI USB Type-C HUB, with super-soft and knot-free silicone woven design cable, meets most mobile office needs. Compact, lightweight, stylish, and powerful portable USB C Hub equipped with 1 x HDMI port, 1 x 100W charging, and 3 x USB ports. 18-month warranty, 24-hour response, to ensure you feel at ease when using our product.
- Design centered on comfort and reliability: Thanks to BENFEI's end-to-end in-house cable production capability, in-house PCBA and assembly capability, using the industry's most advanced silicone woven design and process, 20cm cable in length, no knots, super-soft, the HUB is easy to use in all scenarios: laptop, tablet, stand etc. Super-soft, 25000+ life cycles, to meet your daily carrying and office needs.
- 100W Charging: Support up to 90W USB C pass-through charging via Type-C port to keep your laptop powered. 10W is reserved for other interface operations. No data and video function on the Type-C port.
- 4K HDMI Display: The HDMI port supports media display at resolutions up to 4K 30Hz, keeping every incredible moment detailed and ultra vivid. Please note that the C port of the Host device needs to support video output.
- Transfer Files in Seconds: Transfer files and from your laptop at speeds up to 10 Gbps with USB A 3.2 port. Extra 2 USB A 2.0 ports are perfectly for your keyboards and mouse.
What manufacturing and safety constraints belong in the decision?
Compare total process cost, not just kilogram price. Include dies or tooling, warm-forming equipment, machining allowances, scrap and recycle handling, surface treatment, nondestructive inspection, and certification. Add supplier minimum order quantities, lead time for specialty grades, and the cost of holding certified material in inventory.
Free tools Windows power users keep installed
One-click scans. No signup required.
Magnesium can machine efficiently, but chips and dust can ignite. Use the facility’s qualified procedures for chip size, coolant selection, collection, housekeeping, ignition control, and fire response. Never describe easy cutting as low-risk cutting. The Sanwa processing guidance discusses forming, machining, and combustible-chip precautions.
For forming, confirm whether the supplier can hold the required temperature and atmosphere, and whether the chosen temper survives the process. For casting, verify fill capability, shrinkage and porosity controls, heat treatment, trimming, and inspection capacity. For machining from stock, price material utilization and chip-handling controls alongside cycle time.
Separate development controls from routine production controls. During development, plan trials for forming windows, tool wear, coating adhesion, and joint assembly. During production, define operator training, chip-container design, housekeeping frequency, coolant monitoring, and response to a hot chip or dust event. A route that is technically feasible but unsupported by the plant’s safety equipment is not a feasible route.
How do you compare cost and availability without compromising the design?
Build a should-cost model with at least five lines: certified material, tooling, conversion, finishing and joining, and inspection or testing. For wrought material, include blank nesting and offcut loss. For castings, include die maintenance, trimming, rejected shots, heat treatment, and any machining fixtures. For all routes, include protective packaging and storage that prevent contamination or coating damage.
Do these 3 things before closing this tab:
1Repair Windows errors before they cause bigger problems2Scan for outdated or missing drivers - takes under a minute3Clear out junk files and repair common Windows errorsAsk suppliers whether they can provide the exact temper, dimensions, chemistry report, mechanical-test report, and traceability required by the contract. A commonly advertised alloy in the wrong form can create a long lead time or force a redesign. Confirm whether the supplier can support first-article inspection and periodic requalification, not just an initial sample.
When comparing an alternate grade, preserve the same acceptance basis. A lower quotation is not comparable if it omits coating, galvanic isolation, production-representative testing, or certification. Record assumptions about annual volume, tooling life, scrap rate, and inspection frequency, then run a sensitivity check for lower volume or a tighter defect limit.
Also popular on Amazon
- 【Read before You Buy】 Note: This adapter is USB 2.0 version and cannot transmit HDM, VGA, or other video signals. Nevertheless, they are fully capable of charging devices,duplicating files, and can be seamlessly integrated with USB-C earphones, wireless network adapters, and SD card adapters.
- 【Easy to Use and Safe】Thanks to modern manufacturing techniques, we've made these adapters sufficiently compact so that they can remain inserted in your device without noticeable protrusion or inconvenience. This means you don't have to constantly plug and unplug them, reducing the likelihood of wear and misalignment, and making them more convenient to carry around.
- 【Reliable Quality】Engineered for enhanced durability, durable aluminum alloy shell material,get excellent wear resistance and heat dissipation,the male USB C and female USB connectors & the male USB and female USB C connectors are designed to be plugged and unplugged up to 20000 times. Provides data transfer, device charging, memory space expansion, and additional computer peripherals.
- 【Think more for you】Do you need to connect a USB-C-enabled device to an odd device that only has USB-A ports? Then these USB-A male to USB-C female adapters are made for you.Simply insert the adapter into the USB-A port on the device, and you can instantly connect your USB-C device to the device that originally didn't have the correct connection port.
- 【Trusted xiwxi Quality and Service】As a responsible brand seller, you will receive xiwxi's 12-month Quality assurance and lifetime friendly customer service, you're not just buying a product,you're investing in peace of mind with all-round quality and exceptional customer service.
How do you validate a supplier and specification?
- Name the alloy and form: for example, AZ31B sheet, AZ91D die casting, or a specified extrusion.
- State condition and temper: include heat treatment and orientation requirements where applicable.
- Cite the invoked specification: include revision, dimensions, chemistry limits, mechanical tests, inspection, and acceptance criteria.
- Require certification: obtain heat or lot traceability, chemistry, tensile data, temper evidence, and any casting-quality records.
- Define design data: identify the allowable source, statistical basis, temperature range, fatigue basis, and knockdowns.
- Qualify the process: approve forming, casting, machining, coating, joining, and inspection procedures on representative geometry.
MMPDS-2024, Volume I, Chapter 4 separates wrought and cast alloys and lists grades such as AZ31B, AZ61A, WE43, ZK60A, AZ91C/AZ91E, EV31A, QE22A, EZ33A, and ZE41A. SAE’s magnesium index displayed AMS4437G for AZ91C-T6 castings as current on June 17, 2025. Treat those entries as starting points; recheck the live revision and the specification invoked by your contract.
Read the scope and product-form limits of every specification. Confirm whether the listed properties apply to the thickness, casting method, heat treatment, and test orientation you will purchase. Require the supplier to identify any deviations, substitutions, or rework, and define who has authority to approve them. If a supplier proposes a different alloy designation, obtain a documented equivalency review rather than accepting a verbal comparison of nominal chemistry.
Outdated Drivers Are Slowing You Down
One free scan finds every outdated or missing driver and matches the right update for your exact hardware.Free scan · exact hardware matchWindows Errors? Fix Them Before They Spread
Repair common Windows errors and clear accumulated junk for a smoother, more stable PC - no reinstall needed.Free scan · no reinstallWhat common selection mistakes should you avoid?
- Ranking by tensile strength alone: this ignores stiffness, fatigue, elongation, creep, and local casting quality.
- Mixing product forms: a wrought-sheet value cannot be applied directly to a die-cast boss or machined extrusion.
- Ignoring orientation and temper: rolling or extrusion direction and heat treatment can change the governing allowable.
- Assuming a manual listing is an approval: a grade listed by MMPDS still needs a project-specific specification and data review.
- Leaving galvanic protection until assembly: bolt, washer, coating, sealant, and drainage choices must be designed together.
- Using a coupon as a production guarantee: separately cast specimens do not capture every wall thickness, pore population, or process location.
- Underpricing safety: combustible chips, dust collection, housekeeping, and fire response belong in the route cost and risk assessment.
- Buying a marketplace listing as certified material: an online description may omit temper, revision, chemistry limits, and lot traceability.
What does a defensible selection workflow look like?
- Freeze the route and form. Eliminate grades unavailable in the required sheet, extrusion, forging, casting, or stock form.
- Map loads to properties. Set strength, stiffness, fatigue, impact, elongation, joining, and dimensional requirements.
- Apply temperature and creep filters. Use time-dependent data for every sustained hot load.
- Assess the assembled environment. Address galvanic couples, moisture, salt, chemicals, coatings, drainage, and maintenance.
- Compare process capability. Include tooling, forming temperature, porosity risk, machining, scrap, safety, and inspection.
- Verify supply and data. Confirm specification revision, temper, certification, allowables, and lot traceability.
- Qualify the final design. Test representative parts or coupons through the required production and environmental conditions, then update the drawing and procurement documents.
A lightweight design is successful only when mass reduction survives these checks. A nominally stronger alloy can be the wrong choice if it cannot be formed, corrodes at the joint, creeps at temperature, or lacks certifiable data in the required product form. Keep the decision matrix with the drawing and purchasing specification so that later substitutions are evaluated against the same load, environment, process, and evidence requirements.
Frequently Asked Questions
Can I substitute AZ91D for AZ31B if the strength numbers look similar?
No. AZ91D is primarily a die-casting grade, while AZ31B is commonly supplied as wrought sheet, plate, extrusions, and structural sections. Substitution changes manufacturability, defect structure, anisotropy, joining, corrosion behavior, and the applicable specification, so it requires a new design and qualification review.
Does a lower-density magnesium alloy always make the lightest part?
Not necessarily. Magnesium density is roughly 1.74 g/cm³ in NADCA’s guidance, but its lower stiffness than steel or aluminum can require thicker sections or extra ribs. Compare mass at the required stiffness, buckling margin, fatigue life, and manufacturing constraints—not density alone.
Which alloy is best for a lightweight structural part?
There is no universal best grade. AZ31B is a logical starting point for wrought sheet, plate, extrusions, and structural sections; AZ91D is a common high-strength die-casting benchmark; AM-series grades are candidates when elongation and impact tolerance matter; AS41B and AE42 warrant review for elevated-temperature or creep demands. The final choice must match the exact form, condition, loads, environment, and certified data.
How can I protect magnesium where stainless-steel bolts are unavoidable?
Use a qualified coating or conversion treatment, electrically isolate the bolt with washers or sleeves, seal and drain the joint, and protect cut edges and threads. The isolation system must be designed for preload, wear, temperature, and maintenance; a coating on the exposed panel alone may not stop galvanic attack.
Can magnesium be cold-formed like aluminum?
Not generally. Magnesium’s hexagonal close-packed structure makes room-temperature plastic forming difficult. Warm or hot forming may be required, especially for tight bends, deep draws, or complex profiles. Establish temperature, lubrication, bend radius, springback, and post-forming requirements with the processor.
The Bottom Line
Choose magnesium by route, form, load case, temperature, interfaces, process safety, and certified data—not by alloy name or density alone. Shortlist grades such as AZ31B, AZ91D, AM-series, AS41B, or AE42 only after confirming that the required product form, specification, supplier evidence, and assembly protection are available.

