Do these 3 things before closing this tab:
1Repair Windows errors before they cause bigger problems2Scan for outdated or missing drivers - takes under a minute3Clear out junk files and repair common Windows errorsSome links on this page are affiliate links: if you buy through them we may earn a commission, at no extra cost to you.
An automated metals-testing system is worth buying only when its measurement method, sample handling, software, capacity, and site requirements match your actual laboratory or production workflow. Start by defining the result you need—mechanical properties, chemical composition, or both—then specify representative samples, applicable standards, unattended steps, throughput, traceability, and acceptance criteria before comparing equipment.
Mechanical test automation and chemical-analysis automation are different categories. A tensile-testing line may identify, measure, load, test, sort, and report specimens, while an OES/XRF automation cell may prepare samples, operate analyzers, route results, and manage exceptions. The checklist below helps you separate those use cases and build a defensible request for quotation.
As an Amazon Associate I earn from qualifying purchases.
PC Slower Than It Used to Be?
A free scan shows the junk files, broken settings and background clutter dragging Windows down - then fixes them in one click.Free scan · Windows 10 & 11Crashes, No Sound, or Screen Glitches?
Random freezes, missing sound and display glitches usually trace back to one bad driver. Find and replace yours safely.Free scan · under a minuteWhat result must the system deliver?
Write the required report before looking at product names. State the property or composition to be measured, the test method, customer specification, reporting limits, sample identity rules, and the standards edition that governs acceptance.
| Required result | Typical automation category | Questions to settle first |
|---|---|---|
| Tensile strength, yield strength, elongation, reduction of area | Mechanical specimen-handling and testing line | Specimen geometry, load range, extensometer method, strain rate, sorting rules, and applicable standards |
| Hardness or surface condition | Mechanical line with additional measurement modules | Whether hardness or roughness is in-line, off-line, or a separate operation |
| Elemental composition | OES and/or XRF laboratory automation | Alloy families, detection limits, calibration, surface preparation, and matrix effects |
| Mechanical and chemical release decision | Integrated or coordinated workflows | How results from separate instruments are joined to one sample record and release status |
For mechanical testing, the Instron Automated Metals Testing System document describes support for ASTM E8, EN 10002-1, ISO 6892, and other metals standards, including JIS and DIN. Treat that as a starting point, not proof that every current configuration meets every current edition. Ask the supplier to identify the exact machine, fixtures, software, calibration and extensometer arrangement required for your edition of the standard.
Popular on Amazon
- 【90 Degree Full Function USB C Adapter】Supports the latest USB4 standard for up to 40Gbps of bandwidth, 8K video support, and up to 240W Fast charging; Support USB PD 3.1 Extended Power Range (EPR) including 140W, 180W and 240W. Your productivity is easily doubled. *Warm Tip: For the best fit, please make sure the USB-C port is fully exposed; thick or bulky cases may affect compatibility.
- 【Reliable Quality】Made from high-quality, scratch-resistant aluminum alloy, delicate metal frame. get excellent wear resistance and heat dissipation. Non-Slip Design for easier insertion and removal.
- 【Small and portable】Ultra thin size, ultra compact design, a petite physique that matches the minimalist design of your modern laptops. Coming with a slim figure that won't block the port next to the one it's plugged into.
- 【Compatibility】Widely work with most usb c, thunderbolt 4/3 devices. Compatibilit for ROG Ally, Steam Deck, Switch, MacBook Pro, Quest 3 VR headset, Surface Book 2, iPhone 18/17/16/15, Samsung Galaxy S23/S22/S21, Note 20/10, Google Pixel, ChromeBook, etc.
- 【Excellence Customer Support】If you experience any issues or cable failure, simply reach out to our dedicated customer service team. We provide a prompt response within 18 hours, providing you with the necessary technical support to resolve any concerns.
For chemical analysis, decide whether OES, XRF, or both are appropriate for the matrix and reporting limits. The available evidence identifies XRF, ICP, and mobile or stationary arc/spark analyzer categories, but method selection still requires an application review with representative material and certified reference samples.
What is the difference between mechanical-test and chemical-analysis automation?
Mechanical automation moves physical specimens through a load-and-measure sequence; chemical-analysis automation prepares a surface or portion of material and routes it to an analyzer. They should be compared within their own category because their sample constraints, cycle times, validation evidence, and failure modes are not interchangeable.
Free tools Windows power users keep installed
One-click scans. No signup required.
Mechanical testing lines
A mechanical line generally needs specimen identification, orientation, dimensional measurement, loading, gripping, testing, extensometer handling, pass/fail logic, sorting, and result transfer. The Instron system description includes barcode reading, in-line automatic specimen measurement, specimen racks, pass/fail sorting, extensometer compatibility, and optional Rockwell hardness or surface-roughness measurement. It lists frame capacities of 50, 100, 250 and 600 kN and more, but the correct capacity depends on the loads and fixtures in your test plan.
The same document says its racks can hold up to 400 specimens depending on size and geometry. That is a stated feature of the described system, not a universal capacity or a promise that 400 of your specimens will fit. Require a layout using your longest, widest and heaviest specimens, including rejected or re-test pieces.
Chemical-analysis automation
OES/XRF automation can include sample registration, milling or grinding, sawing, crushing, pelletizing, analyzer loading, cleaning, result review, sorting and data transfer. Thermo Fisher’s automation overview describes systems that coordinate preparation and analysis and can perform parallel tasks. Confirm which of those tasks are included in the proposed cell rather than assuming that an automated loader represents a fully unattended laboratory.
How should sample fit and preparation be evaluated?
Provide the vendor with a real sample catalogue, not a generic description such as “steel billets” or “tensile bars.” Include shape, length, width, thickness, diameter, mass, surface condition, hardness, temperature, contamination, allowable preparation, and the percentage of nonconforming pieces.
Thermo Fisher’s ARL SMS-3500 Entry brochure gives different thickness ranges for OES and XRF and specifies parallel surfaces for XRF. It also lists milling, grinding, sawing, crushing and pelletizing options for different sample types. Those details illustrate why a configuration cannot be selected from analyzer brand or throughput alone: the preparation machine, tooling and sample presentation can determine whether the promised workflow is possible.
Ask for an explicit “in scope/out of scope” matrix covering:
- Minimum and maximum dimensions, thickness and mass for each sample family.
- Surface flatness, parallelism, roughness and cleanliness requirements.
- Whether hot, oily, painted, oxidized, wet or irregular samples can be accepted.
- Preparation media, tooling wear, swarf or dust control, and waste handling.
- Manual intervention required for unusual geometry, failed preparation or re-analysis.
- How samples are returned, retained, quarantined or destroyed after testing.
Have the supplier demonstrate the hardest sample class in your catalogue. A system that handles common samples smoothly may still require a manual lane for odd dimensions, small pieces or heavily contaminated surfaces.
Also popular on Amazon
- 5-in-1 Connectivity: Equipped with a 4K HDMI port, a 5 Gbps USB-C data port, two 5 Gbps USB-A ports, and a USB C 100W PD-IN port. Note: The USB C 100W PD-IN port supports only charging and does not support data transfer devices such as headphones or speakers.
- Powerful Pass-Through Charging: Supports up to 85W pass-through charging so you can power up your laptop while you use the hub. Note: Pass-through charging requires a charger (not included). Note: To achieve full power for iPad, we recommend using a 45W wall charger.
- Transfer Files in Seconds: Move files to and from your laptop at speeds of up to 5 Gbps via the USB-C and USB-A data ports. Note: The USB C 5Gbps Data port does not support video output.
- HD Display: Connect to the HDMI port to stream or mirror content to an external monitor in resolutions of up to 4K@30Hz. Note: The USB-C ports do not support video output.
- What You Get: Anker 332 USB-C Hub (5-in-1), welcome guide, our worry-free 18-month warranty, and friendly customer service.
Which workflow steps are actually unattended?
Draw the process as individual operations and mark each one as automatic, operator-assisted, or manual. “Robot loading” is only one step and does not necessarily include preparation, cleaning, result verification, exception recovery or database release.
- Registration: barcode, label, job file or operator entry.
- Identification and orientation: reading the code, locating features and confirming the correct recipe.
- Preparation: cutting, milling, grinding, crushing, pelletizing or dimensional measurement.
- Instrument loading: gripping, positioning, clamping and fixture verification.
- Measurement: test execution, analyzer acquisition, calibration checks and repeat runs.
- Cleaning: chip removal, surface cleaning, analyzer cleaning and cross-contamination control.
- Disposition: pass/fail sorting, quarantine, re-test routing and sample return.
- Data handling: result review, audit trail, report generation and LIMS or database transfer.
- Exception handling: jam recovery, invalid barcode, failed preparation, network loss and analyzer fault.
Request a demonstration of an intentionally failed sample and a disconnected-network scenario. The important question is not whether the cell stops safely; it is whether it records the event, preserves the sample identity, prevents an incorrect release and gives an operator a clear recovery path.
How should throughput claims be compared?
Compare complete, representative cycle time—not the analyzer’s headline acquisition time. Include loading, preparation, measurement, cleaning, re-preparation, repeats, operator intervention, result review and release to the next system.
Thermo Fisher states that the ARL SMS-3300 supports a cadence of more than 1,000 samples per day. This is a vendor capability claim, not an independent guarantee. Ask the supplier to model that cadence using your sample mix, preparation method, number of analyzers, calibration frequency, planned operating hours and expected exception rate.
Put the model in writing with at least three scenarios:
- Normal mix: the percentages of each routine sample type.
- Peak shift: the largest hourly or daily intake and available buffer.
- Disruption: one analyzer unavailable, a preparation tool change, a failed sample or a network interruption.
Define throughput as accepted results released to the intended database or LIMS. A counter showing pieces entering a cell is not equivalent to validated results available for a production decision.
What traceability and software features matter?
Traceability should connect the physical sample, test recipe, preparation events, instrument data, operator actions and final disposition. Confirm whether the system provides:
- Barcode or other unambiguous sample registration.
- Time-stamped event history for loading, preparation, measurement, cleaning, re-test and sorting.
- Recipe and method version control, including who changed a parameter.
- Role-based permissions for operators, supervisors, quality personnel and administrators.
- Raw data retention and links to calibration or reference-material checks.
- Interfaces for your LIMS, manufacturing database, historian or quality system.
- Duplicate detection, missing-result alerts and controlled result release.
- Recovery after power, network or analyzer interruptions without losing sample identity.
Thermo Fisher describes sample registration, event traceability and laboratory data-management features in its automation material. Instron describes barcodes and database/LIMS result transfer. Ask for the interface specification, supported protocols, data ownership, export format, cybersecurity controls and validation documentation before signing a purchase order. “Can export a CSV” may not satisfy an audited workflow that requires immutable event records and role controls.
How should capacity, redundancy and expansion be sized?
Size the system for the highest sustained workload and the worst credible peak, then decide how much redundancy is financially and operationally justified. Compare sample buffer capacity, number of preparation machines, number of analyzers, parallel paths, maintenance bypasses and expansion space.
Also popular on Amazon
- Sleek 7-in-1 USB-C Hub: Features an HDMI port, two USB-A 3.0 ports, and a USB-C data port, each providing 5Gbps transfer speeds. It also includes a USB-C PD input port for charging up to 100W and dual SD and TF card slots, all in a compact design.
- Flawless 4K@60Hz Video with HDMI: Delivers exceptional clarity and smoothness with its 4K@60Hz HDMI port, making it ideal for high-definition presentations and entertainment. (Note: Only the HDMI port supports video projection; the USB-C port is for data transfer only.)
- Double Up on Efficiency: The two USB-A 3.0 ports and a USB-C port support a fast 5Gbps data rate, significantly boosting your transfer speeds and improving productivity.
- Fast and Reliable 85W Charging: Offers high-capacity, speedy charging for laptops up to 85W, so you spend less time tethered to an outlet and more time being productive.
- What You Get: Anker USB-C Hub (7-in-1), welcome guide, 18-month warranty, and our friendly customer service.
Thermo Fisher positions the SMS-2300 for lower-volume work, the SMS-3300 for medium volume and the SMS-3500 for high volumes, with options for single or multiple analyzers and preparation equipment. These are vendor positioning statements. Convert your own workload into samples per shift, samples by type, peak arrival rate and required result-release time before selecting a model.
Ask these capacity questions:
- How many samples can wait safely in the input and output buffers?
- Can one analyzer or preparation machine be isolated while the rest of the line continues?
- Can a second analyzer, preparation module or storage rack be added later?
- What happens to samples already in process when a module fails?
- Is there a manual bypass for urgent production or quality investigations?
- How are re-tests and calibration samples prioritized against production samples?
Redundancy is useful only if software, utilities, fixtures and trained staff support it. A second analyzer that cannot use the same method, calibration or preparation route may not provide meaningful backup.
What site and utility requirements should be checked?
Obtain a dimensioned layout and utility schedule before approving the purchase. Include operator access, guarding, maintenance clearance, sample transport, waste, ventilation, noise, environmental limits, floor loading and future expansion—not just the machine footprint.
One ARL SMS-3500 Entry configuration is listed at approximately 4,370 × 2,725 × 1,905 mm and around 800 kg before analyzers and sample-preparation equipment. The brochure lists 400 V three-phase power and compressed air. Treat those figures as configuration-specific and verify the final arrangement, local electrical requirements, air quality, pressure, flow and any ventilation or extraction needs with the supplier.
Recommended Free Tools
Your site-readiness checklist should cover:
- Incoming power, disconnects, grounding and backup strategy.
- Compressed air capacity, filtration, dryness and redundancy.
- Ventilation, dust or swarf extraction, coolant and waste collection.
- Floor loading, anchoring, vibration and access for delivery.
- Guarding, interlocks, emergency stops and safe operator routes.
- Temperature, humidity, cleanliness and environmental limits for analyzers.
- Network drops, segmented access, data backup and cybersecurity review.
- Crane, doorway, lift and staging requirements for installation and service.
How should standards, calibration and validation be handled?
Ask the supplier to map every required result to the current standard edition, equipment configuration, fixture, software calculation and calibration procedure. Do not accept a broad statement that a product is “designed for” a standard without seeing the compliance assumptions.
For mechanical testing, define gauge-length measurement, strain rate, extensometer use, alignment checks, load-cell class, dimensional measurement and reporting rules. For OES/XRF, define calibration strategy, reference materials, drift checks, surface preparation, spectral or matrix corrections, detection limits and re-analysis rules.
Build validation into procurement. Provide representative samples spanning the expected composition, geometry and result range. Specify repeatability, reproducibility, bias, reportable resolution, false-pass prevention and maximum allowed invalid-result rate. If the system will support a regulated or customer-audited process, identify required software validation, electronic records, signatures, retention and change-control evidence early.
What should a witnessed site-acceptance test include?
A witnessed site-acceptance test should prove the complete workflow with your samples, methods and data destination. The reviewed material contains no independent comparative performance study, so buyer-specific acceptance evidence is especially important.
- Sample challenge: run routine, borderline, awkward and deliberately nonconforming samples.
- Method challenge: use the actual recipes, standards, fixtures, calibrations and reporting limits.
- Accuracy and repeatability: compare results with agreed reference values and replicate runs.
- Throughput: measure accepted, released results over a representative operating period, including preparation and cleaning.
- Traceability: verify barcode identity, event timestamps, audit records and final database/LIMS entries.
- Fault recovery: interrupt power or network connections under controlled conditions, create a failed preparation, and test analyzer or robot recovery.
- Safety: verify guarding, interlocks, emergency stops and safe manual recovery.
- Documentation: collect as-built drawings, software versions, calibration certificates, maintenance schedules, spare-parts lists and training records.
Write pass/fail criteria into the contract before the test. Specify what happens when a criterion fails: corrective action, repeat demonstration, withheld payment, or acceptance with a documented deviation.
Also popular on Amazon
- Portable and powerful USB-C HUB: BENFEI USB Type-C HUB, with super-soft and knot-free silicone woven design cable, meets most mobile office needs. Compact, lightweight, stylish, and powerful portable USB C Hub equipped with 1 x HDMI port, 1 x 100W charging, and 3 x USB ports. 18-month warranty, 24-hour response, to ensure you feel at ease when using our product.
- Design centered on comfort and reliability: Thanks to BENFEI's end-to-end in-house cable production capability, in-house PCBA and assembly capability, using the industry's most advanced silicone woven design and process, 20cm cable in length, no knots, super-soft, the HUB is easy to use in all scenarios: laptop, tablet, stand etc. Super-soft, 25000+ life cycles, to meet your daily carrying and office needs.
- 100W Charging: Support up to 90W USB C pass-through charging via Type-C port to keep your laptop powered. 10W is reserved for other interface operations. No data and video function on the Type-C port.
- 4K HDMI Display: The HDMI port supports media display at resolutions up to 4K 30Hz, keeping every incredible moment detailed and ultra vivid. Please note that the C port of the Host device needs to support video output.
- Transfer Files in Seconds: Transfer files and from your laptop at speeds up to 10 Gbps with USB A 3.2 port. Extra 2 USB A 2.0 ports are perfectly for your keyboards and mouse.
What information should an RFQ contain?
A detailed RFQ produces more comparable proposals and exposes hidden assumptions. Include the following attachments and questions:
- Sample drawings, photographs, dimensions, mass ranges and surface conditions.
- Annual, monthly, shift and peak-hour volumes by sample type.
- Required methods, standards editions, customer specifications and reporting limits.
- Required outputs, units, rounding, pass/fail logic and report templates.
- Preparation steps that are mandatory, optional or prohibited.
- Required unattended hours and operator coverage by shift.
- Barcode, naming, recipe and LIMS/database interface requirements.
- Site drawings, available power, compressed air, ventilation and network details.
- Accuracy, repeatability, throughput, traceability and recovery acceptance criteria.
- Installation, commissioning, training, preventive maintenance, calibration and response-time expectations.
- Consumables, tooling wear, software licenses, upgrades, spare parts and warranty assumptions.
- Expansion options, manual bypasses and redundancy requirements.
Require each bidder to identify exclusions, assumptions and recurring costs separately from capital equipment. This prevents a low initial quote from hiding preparation tooling, integration work, utilities, validation support or service obligations.
Independent reader supportYour contribution helps us test, update, and keep practical guides available for everyone.What does the available equipment evidence show?
Instron mechanical automation
The described system combines specimen racks, barcode reading, in-line measurement, automated handling, testing, pass/fail sorting, extensometer compatibility and optional hardness or surface-roughness measurement. It lists frame capacities from 50 to 600 kN and higher options and states storage capacity of up to 400 specimens depending on geometry. Its brochure also uses the phrase “Robotic specimen handling eliminates human variation in testing.” That statement describes the manufacturer’s rationale; buyers should still verify repeatability and method compliance with their own acceptance samples.
The Tool Desk
Outbyte Driver Updater FREEFix the driver behind crashes, sound loss and screen glitchesFind Drivers →Outbyte PC Repair FREERepair Windows errors before they cause bigger problemsFix Now →The document is older than some current product literature. Confirm current availability, model names, software revisions, standards editions, safety requirements and service coverage directly in the quotation.
Thermo Fisher ARL SMS automation
The ARL SMS portfolio covers OES and/or XRF configurations. The published selection guide positions SMS-2300, SMS-3300 and SMS-3500 for lower, medium and high volume respectively, while allowing different combinations of analyzers and preparation equipment. The SMS-3300 brochure claim of more than 1,000 samples per day and the SMS-3500 Entry brochure’s storage magazine of 45 samples, expandable to 90, are useful sizing references but remain configuration-dependent vendor claims.
The SMS-3500 Entry material also describes an optional introduction magazine for up to 32 production samples. Ask whether that magazine, storage rack, preparation module and analyzer arrangement match your sample geometry and whether the quoted capacity includes re-tests, calibration pieces and rejected samples.
Method-selection context
SPECTRO’s pages for metal producers and metal testing describe XRF, ICP, and mobile or stationary arc/spark analyzer categories. The available excerpts suggest simpler preparation for XRF and sensitivity or automation opportunities for ICP, but they are not a complete technical comparison. Use them as prompts for an application discussion, then require method-specific evidence on your alloys, limits and preparation process.
What’s actually slowing this PC down?
Pick the symptom - the matching free tool is one click away.
What are the most common buying mistakes?
- Choosing by robot or analyzer alone: the surrounding preparation, fixtures, software and exception handling determine the real workflow.
- Using average volume: peak arrivals and result-release deadlines often drive buffer and redundancy requirements.
- Accepting headline cadence: ask whether the figure includes preparation, cleaning, repeats, review and released results.
- Ignoring difficult samples: irregular, contaminated or thin samples can create a manual bottleneck.
- Leaving integration until late: barcode rules, LIMS mapping, role controls and audit records affect both price and commissioning.
- Underestimating utilities: power, compressed air, extraction, floor loading and maintenance access can require facility work.
- Skipping failure tests: a system must preserve identity and data when a sample, network or module fails.
- Comparing unlike categories: mechanical testing lines and OES/XRF preparation cells answer different questions.
- Relying on an old brochure: confirm current configuration, standards, software, service terms and parts availability in writing.
How can buyers make the final decision?
Score each proposal against the same weighted criteria and document evidence, not sales language. A practical weighting is measurement suitability first, then sample fit, workflow coverage, validated throughput, traceability, site fit, service and lifecycle cost. Adjust the weighting when a customer specification or safety requirement makes one criterion non-negotiable.
For each criterion, record the supplier’s evidence: specification, drawing, interface document, sample demonstration, reference installation, acceptance-test commitment or unresolved assumption. Mark unsupported claims for clarification rather than awarding full credit.
Also popular on Amazon
- 【Read before You Buy】 Note: This adapter is USB 2.0 version and cannot transmit HDM, VGA, or other video signals. Nevertheless, they are fully capable of charging devices,duplicating files, and can be seamlessly integrated with USB-C earphones, wireless network adapters, and SD card adapters.
- 【Easy to Use and Safe】Thanks to modern manufacturing techniques, we've made these adapters sufficiently compact so that they can remain inserted in your device without noticeable protrusion or inconvenience. This means you don't have to constantly plug and unplug them, reducing the likelihood of wear and misalignment, and making them more convenient to carry around.
- 【Reliable Quality】Engineered for enhanced durability, durable aluminum alloy shell material,get excellent wear resistance and heat dissipation,the male USB C and female USB connectors & the male USB and female USB C connectors are designed to be plugged and unplugged up to 20000 times. Provides data transfer, device charging, memory space expansion, and additional computer peripherals.
- 【Think more for you】Do you need to connect a USB-C-enabled device to an odd device that only has USB-A ports? Then these USB-A male to USB-C female adapters are made for you.Simply insert the adapter into the USB-A port on the device, and you can instantly connect your USB-C device to the device that originally didn't have the correct connection port.
- 【Trusted xiwxi Quality and Service】As a responsible brand seller, you will receive xiwxi's 12-month Quality assurance and lifetime friendly customer service, you're not just buying a product,you're investing in peace of mind with all-round quality and exceptional customer service.
The strongest proposal is not necessarily the fastest machine. It is the configuration that can produce the required result on your samples, preserve an auditable identity trail, recover safely from predictable failures, fit the facility and remain supportable after installation.
What should happen after the purchase order?
Assign owners for application engineering, facility work, IT/security, quality validation, operator training and acceptance. Freeze sample and method definitions early, review interface mappings before software configuration, and schedule a staged commissioning plan: utilities and safety, dry runs, sample handling, instrument calibration, integrated workflow, then witnessed acceptance.
Quick wins for a faster PC:
Fix the driver behind crashes, sound loss and screen glitchesFind Drivers →Repair Windows errors before they cause bigger problemsFix Now →Maintain a controlled list of software versions, recipes, fixtures, calibration materials, consumables and spare parts. Define who can change methods and how changes are revalidated. Automation reduces repetitive handling, but it does not remove the need for competent operators, quality oversight and a documented response to exceptions.
Bottom line: buy the result and the complete workflow, not a robot or analyzer in isolation. Define methods and sample limits first, model throughput with real exceptions, verify software and utilities, and make representative-sample acceptance testing a contractual requirement.
Frequently Asked Questions
Can one automated line perform both tensile testing and alloy analysis?
Usually these are separate automation domains with different handling and preparation requirements. They can be coordinated through shared sample identification and a LIMS or database, but confirm whether a proposed integration joins results into one controlled record or merely places two instruments near each other.
Are vendor sample-per-day figures guarantees?
No. Published cadence figures describe a stated capability for a particular configuration and operating assumption. Ask for a workload model using your sample mix, preparation steps, repeats, cleaning, staffing and result-release rules, then verify it during acceptance.
What should be included in an automated metals-testing service contract?
Specify preventive-maintenance intervals, calibration support, response and restoration targets, remote-access rules, critical spare parts, consumable lead times, software updates, training refreshers and the escalation path for unresolved faults. Require the supplier to state which tasks are excluded from the base service.
Do XRF samples need special preparation?
Preparation depends on material and configuration, but the cited SMS-3500 Entry documentation identifies parallel surfaces for XRF and lists options such as milling, grinding, sawing, crushing and pelletizing. Have the supplier confirm the exact surface, thickness and cleanliness requirements for every sample family.

