Do these 3 things before closing this tab:
1Clear out junk files and repair common Windows errors2Fix the driver behind crashes, sound loss and screen glitches3Repair Windows errors before they cause bigger problemsShort answer: Larix Broadcaster can publish over SRT, but SRT works only when the receiving server supports it. YouTube’s current encoder guidance lists RTMP/RTMPS, not a general direct SRT endpoint. Check the intended channel’s Live Control Room before configuring Larix; if it offers RTMP/RTMPS only, send SRT to a compatible relay and have that relay publish to YouTube—or use RTMPS directly from Larix.
For a 24/7 stream, choose a video profile your phone and sustained internet upload can maintain, match Larix’s SRT mode and connection details to the receiver, and test recovery and power behavior. SRT settings alone cannot make a mobile device reliably run unattended around the clock.
As an Amazon Associate I earn from qualifying purchases.
Can Larix Broadcaster send SRT directly to YouTube Live?
Larix supports SRT publishing, including Push (Caller), Listener and Rendezvous modes. These describe how Larix connects to an SRT receiver; they do not make YouTube the receiver or supply a YouTube SRT address. YouTube’s current encoder guidance lists RTMP/RTMPS, and its stream settings are managed in Live Control Room. Check the actual options for the channel you intend to stream to before assuming direct SRT ingest is available.
Quick wins for a faster PC:
Clear out junk files and repair common Windows errorsFree Scan →Fix the driver behind crashes, sound loss and screen glitchesFind Drivers →If Live Control Room provides only RTMP/RTMPS, there are two practical paths: publish to YouTube using that protocol directly from Larix, or send an SRT contribution to a compatible relay that republishes to YouTube over a supported ingest protocol. A relay adds another service and connection to configure and monitor. Do not guess an SRT URL, port, stream ID, passphrase or latency value.
#1 Best Overall
- 4K & HD STREAMING IN H.264 AND H.265 – Self-contained processor supporting H.264 and H.265 encoding in HD or Ultra HD (up to 2160p60) via SRT or RTMP, streaming directly to YouTube, Facebook, X, Twitch, Zoom, Microsoft Teams, OBS, Wowza, and many more — no encoding PC needed.
- 12G-SDI INPUT WITH STANDARDS CONVERSION – Supports input resolutions up to DCI 4K60 with an SDI input and SDI loop output, plus Teranex-powered automatic standards conversion so any HD or Ultra HD source streams cleanly at any target resolution.
- DUAL MONITOR OUTPUTS – Features both SDI and HDMI monitor outputs with a user-configurable standards converter on both the 12G-SDI Out and 4K HDMI Out, so you can feed a confidence monitor or downstream device at any required format independent of your streaming standard.
- ETHERNET + 5G/4G MOBILE WITH AUTO-FAILOVER – Connect via Gigabit Ethernet (10/100/1000BASE-T) or tether a smartphone via USB-C for mobile data, with automatic switchover between connections — ensuring your stream stays on air even if the primary internet connection drops.
- CLOSED CAPTIONS, TIMECODE & REST API – Supports embedding CEA-608 and CEA-708 closed captions in live RTMP streams, source timecode over RTMP and SRT, and offers a REST API over Ethernet for external HTTP control — ideal for broadcast automation and accessibility-compliant workflows.
YouTube Live Control Room is where you can check stream setup and manage stream settings. YouTube’s encoder settings and bitrates describe its current encoder guidance.
Choose a connection path
| Path | What connects to what | What to verify | Trade-off |
|---|---|---|---|
| Direct RTMPS from Larix | Larix publishes to the YouTube endpoint using the channel’s stream key. | Use the endpoint and key shown in Live Control Room, and configure Larix for the protocol and encoder profile YouTube supports. | Fewer services and links in the chain; no SRT contribution leg. |
| SRT to a relay, then YouTube | Larix publishes SRT to a compatible receiver; the relay sends the feed onward to YouTube using a supported ingest path. | Obtain the receiver’s exact SRT address, port, mode and any stream ID or passphrase. Configure the relay’s YouTube output separately. | Allows SRT recovery controls on the contribution leg, but adds relay configuration and another possible failure point. |
The available guidance does not establish a particular relay product or confirm that SRT ingest is enabled for every YouTube channel. Confirm the endpoint with the receiving service and the channel’s Live Control Room.
Set the SRT options to match the receiver
In Larix, create or edit an SRT connection using the values supplied by the receiving server. Softvelum’s documentation advises using video-plus-audio mode, setting an appropriate bitrate and following the receiver’s requirements. The relevant controls are connection parameters, not universal YouTube values.
Rank #2
- H.264
- H.265 Stream
- 1080p 60fps
- 12G-SDI In/Loop Out
Mode: Push (Caller), Listener or Rendezvous
- Push (Caller): Often a suitable arrangement when the phone initiates an outbound connection to a server. Use it only if the receiver is configured for that relationship.
- Listener: Use when the Larix device is expected to listen for an incoming connection and that arrangement is supported by the network and receiver.
- Rendezvous: Use when both ends are configured to establish a rendezvous connection.
The receiver’s setup determines the right mode. If its instructions do not specify one, ask the receiver’s operator rather than choosing by guesswork.
Receiver address, port and stream ID
Copy the SRT listener address and port from the receiving server’s instructions. Add a stream ID only when the receiver requires one, and enter any other connection parameters exactly as supplied. Larix supports SRT parameters such as stream ID; a value that is valid for one receiver is not automatically valid for another.
Passphrase and encryption
Configure encryption only when the receiver supports and requires it, using the receiver’s specified settings. Send passphrases and stream credentials privately. Do not put them in a public stream description, screenshot or support post.
Rank #3
- 【Hardware H.265/H.264 Encoding at 1080P60】Dedicated hardware encoder delivers broadcast-quality 1080P60 streams with H.265/H.264 compression. Reduces bandwidth usage by up to 50% compared to legacy H.264-only solutions, while maintaining crisp, crystal-clear video output.
- 【Broad Protocol Support for IP Distribution】 Supports SRT, RTMP(S), RTSP, UDP, HTTP, HLS, WebRTC, TRTC, Icecast and SHOUTcast — integrate seamlessly with CDNs, surveillance NVRs, IPTV systems and browser-based monitoring dashboards. One device replaces multiple single-purpose streaming boxes.
- 【Browser-Based Setup in Minutes】 Set up in minutes through any browser — no software, drivers or OS compatibility issues. DHCP is enabled by default to prevent IP address conflicts on your network. Note: basic networking knowledge (IP address, RTSP/RTMP configuration) is recommended for advanced streaming setups.
- 【Compact Design with Flexible Deployment】Palm-sized form factor (approx. 90×54×29mm) fits easily behind monitors, on shelves, or in equipment racks. Low power consumption ensures reliable 24/7 operation for live events, remote monitoring, and digital signage.
- 【Professional Audio & OSD Overlay + 1-Year Warranty】 Supports HDMI embedded audio plus external 3.5mm input. Built-in OSD generator adds scrolling text, logos, or timestamps directly to the video stream — ideal for branding, event info, or security labeling. Backed by a 1-year warranty and 24/7 online technical support.
Latency
SRT latency is the recovery window available for handling packet loss on the SRT connection. Softvelum describes recovery as occurring within the latency parameter period. Set it according to measured network jitter and loss and the receiver’s requirements; no universal value is established for this setup. This is different from YouTube’s viewer-facing stream latency setting.
Recommended Free Tools
Bitrate and available bandwidth
Set the Larix video bitrate for the resolution, frame rate and codec you can sustain. Leave capacity for changing network conditions rather than targeting the full measured upload rate. Larix’s bitrate controls differ by platform: its FAQ describes Android bitrate as a typed value and iOS as a selection from predefined values. Actual output can vary by device and encoder, so check the delivered stream rather than assuming the configured target is exact.
Choose a YouTube-facing video and audio profile
YouTube’s current encoder guidance recommends RTMPS and lists H.264, H.265 and AV1 video, up to 60 fps, with constant bitrate (CBR). It recommends a two-second keyframe interval and allows a maximum of four seconds. Supported audio choices listed are AAC and MP3. These are YouTube-facing requirements and recommendations; do not transfer them automatically to an SRT contribution leg without checking the relay and receiver.
Rank #4
- H.264 & H.265 Streaming to SRT or RTMP
- DCI 4K Streaming up to 60 fps
- SDI & HDMI Monitor Outputs
- USB-C for Phone Tethering & Webcam Out
- Front Panel Buttons & Spin Knob
For H.264, YouTube’s guidance accessed in 2026 gives these examples:
| Resolution and frame rate | Published minimum video bitrate | Published recommended video bitrate |
|---|---|---|
| 720p at 30 fps | 3 Mbps | 8 Mbps |
| 1080p at 30 fps | 5 Mbps | 14 Mbps |
| 1080p at 60 fps | 6 Mbps | 17 Mbps |
These are YouTube’s published encoder figures, not a guarantee that Larix on a particular phone will deliver those rates reliably. YouTube advises choosing a quality that suits the available connection, testing with representative movement and audio, and monitoring stream health. Its network guidance recommends about 20% bandwidth headroom. For an always-on mobile setup, a lower, stable profile is generally a more useful starting point than a higher profile that frequently drops frames or disconnects.
Crashes, No Sound, or Screen Glitches?
Random freezes, missing sound and display glitches usually trace back to one bad driver. Find and replace yours safely.Free scan · under a minutePC Slower Than It Used to Be?
A free scan shows the junk files, broken settings and background clutter dragging Windows down - then fixes them in one click.Free scan · Windows 10 & 11Configure and test before leaving the stream unattended
- Confirm the destination. In the channel’s YouTube Live Control Room, identify the available ingest protocol and obtain the correct stream settings. If using SRT, get the receiver’s connection details from the relay or server operator.
- Set up Larix. Choose the mode and enter the endpoint, port, and any required stream ID or encryption values. Select video-plus-audio mode, then set a bitrate, resolution and frame rate the device and connection can sustain.
- Check the YouTube-facing output. For a direct YouTube connection or the relay’s output, use the channel’s supported endpoint and key. Align the output with YouTube’s published encoder guidance, including CBR and the keyframe interval, where the encoder exposes those controls.
- Run a test with representative content. Include the actual audio and typical movement. Check YouTube’s preview and stream health, and confirm the expected picture, sound and stability before relying on the setup. YouTube Help specifically advises testing before starting a live stream.
- Test interruption recovery. Briefly test the network interruption and reconnection behavior you expect to encounter. Observe Larix, the SRT receiver or relay, and YouTube’s output. A reconnect control may help restore a connection, but it is not an uptime guarantee.
- Plan power, heat and monitoring. Use a device-compatible power supply, check the phone and operating system during an extended run, and arrange a stable connection with backup or failover if the stream needs it. Monitor for app suspension, thermal throttling and loss of network access.
Stream-key and account safety
YouTube uses a stream key to let an encoder deliver a feed to the channel. Manage it in Live Control Room and treat it as a secret: anyone who obtains it may be able to send video to your stream. If it is exposed, reset it in the channel’s stream settings and update the encoder or relay that uses it.
Best Value
- DECODE STREAMS BACK TO PROFESSIONAL VIDEO – Converts H.264 or H.265 streams from the Blackmagic Streaming Encoder or compatible Blackmagic cameras back to SDI and HDMI video, delivering broadcast-quality output directly to switchers, monitors, and recording systems at your receive end.
- PAIRS WITH BLACKMAGIC CAMERAS WITHOUT AN ENCODER – Compatible with cameras such as the Blackmagic Studio Camera Pro, PYXIS, URSA Cine, and URSA Broadcast G2, which have built-in streaming, enabling point-to-point remote video links from camera to decoder without any additional hardware at the source.
- RETURN TALLY, CAMERA CONTROL & TALKBACK VIA SDI – A 12G-SDI reference input enables users to send SDI tally, camera control, and talkback back to the encoder end — so your central control room can remotely operate cameras, change settings, and communicate with crew at the remote location, all over the internet.
- ETHERNET + 5G/4G MOBILE WITH AUTO-FAILOVER – Both the front and rear panels include USB-C connectivity for tethering high-speed 5G and 4G phones, and in the event of an internet failure the device automatically switches to the connected phone's mobile data connection — keeping your receive link live even when primary internet fails.
- BLACKMAGIC CLOUD STREAMING SUPPORT – Receive streams distributed via Blackmagic Cloud, enabling cloud-based remote production workflows and multi-location live events without the cost of dedicated broadcast circuits.
Streaming permission does not grant rights to the video or audio you broadcast. Use material you own or are authorized to stream, and review YouTube’s copyright rules and monetization policies for reused content before building a continuous channel around recordings. A 24/7 format does not remove those obligations.
Independent reader supportYour contribution helps us test, update, and keep practical guides available for everyone.What a phone-based 24/7 setup can and cannot guarantee
A 24/7 stream is an operational goal, not a Larix switch. The phone must remain powered, cool enough to encode, connected to the network, and able to keep the app active. The receiver or relay and YouTube must also remain available. Larix exposes reconnect controls, but its documentation does not promise unattended continuous operation or establish that a particular phone will avoid heat, app-suspension or power problems.
Larix’s FAQ describes a reconnect timeout and a network-presence option; it also lists iOS-only settings for reconnecting without a network and for idle or unsent buffer thresholds. These controls can shape recovery behavior on supported devices. Check the current Larix interface and documentation for your platform, and test the behavior in your own setup instead of relying on a setting name as proof of reliability.
Free tools Windows power users keep installed
One-click scans. No signup required.
Troubleshoot common SRT and 24/7 failures
| Symptom | Likely cause | What to check or do |
|---|---|---|
| Larix cannot connect to the SRT destination | Wrong receiver address or port, incompatible mode, blocked network path, or a receiver that is not listening. | Recheck the receiver’s exact settings and required mode, confirm the receiver is available, and verify outbound connectivity on the phone’s network. |
| SRT connects but the relay does not reach YouTube | The relay’s YouTube output, endpoint, stream key or supported protocol is incorrect. | Check the relay’s output status and the channel’s current Live Control Room settings. Keep the SRT contribution configuration separate from YouTube’s ingest settings. |
| Video stutters, drops frames or disconnects | Bitrate is too high for sustained upload, network variation exceeds available headroom, or the device is struggling to encode. | Lower the resolution, frame rate or bitrate; preserve upload headroom; test during representative network conditions; and inspect the device for heat or performance problems. |
| Connection recovers slowly after packet loss | The SRT recovery window may not suit the observed jitter or loss, or the network interruption is beyond what that connection can recover from. | Measure the connection and consult the receiver’s requirements before changing SRT latency. Remember that increasing SRT recovery time can add contribution delay. |
| Stream stops after the phone is left alone | Power interruption, thermal throttling, app suspension, operating-system behavior or loss of network access. | Test an extended run with the intended power supply and network. Check device-specific background and battery settings, temperature and remote monitoring options; Larix reconnect settings cannot correct every device-level failure. |
| YouTube shows an unexpected picture or no audio | Encoder profile, audio mode, or relay output does not match the intended stream. | Inspect the YouTube preview and stream health, confirm video-plus-audio mode where required, and test the full path from Larix through any relay. |
Or let it run in the cloud
If your goal is a continuous YouTube stream made from uploaded videos, StreamNeo is a cloud alternative to keeping Larix and a phone running. Upload a recording or build a playlist, add your YouTube stream key once, and go live. StreamNeo loops uploaded videos from the cloud, so no computer or home connection has to stay on. It streams to YouTube only and does not broadcast from a camera.
- Nothing has to stay on at home; StreamNeo runs the stream in the cloud.
- One price per slot for any quality up to 4K 60 fps as uploaded, with no re-encoding or quality tiers.
- Automatic recovery if YouTube drops the stream.
- The first day is free with no card required; it is one free day per account.
- Monthly: $9.99 per month.
Start your free StreamNeo day.
Frequently Asked Questions
Does SRT latency control YouTube’s stream delay?
No. SRT latency is the recovery window for the SRT connection; YouTube’s viewer-facing latency is a separate setting.
Can I use Larix to stream live camera video through StreamNeo?
No. StreamNeo loops uploaded videos and playlists; it does not go live from a camera.
Quick Recap
Product prices and availability are accurate as of the date/time indicated and are subject to change. Any price and availability information displayed on Amazon at the time of purchase will apply.
What’s actually slowing this PC down?
Pick the symptom - the matching free tool is one click away.
