Choose TTP223 when you need one touch key. Choose a TTP224-family part when you need several independent touch keys. The practical decision is usually that simple, but voltage limits, IC suffixes, module wiring and output modes can change from one board to another. Tontek lists its TTP223 devices as single-key parts and its TTP224C and TTP224B entries as four-key parts. Before ordering, match the exact suffix and read the module documentation rather than treating the family names as complete specifications.
The quick choice: one key or several?
Think of these devices as touch-input controllers rather than complete user interfaces. They sense a change in capacitance at an electrode and present a digital signal that a microcontroller or another circuit can read.
As an Amazon Associate I earn from qualifying purchases.
- Use TTP223 for a single touch button, wake input, lamp control, menu select key or other one-channel function.
- Use a TTP224-family device when the project needs multiple independent touch buttons. The TTP224C and TTP224B listings cited here each describe four touch keys.
- Use a module only after checking its board details. A breakout adds a PCB, indicator, connector or header, configuration pads and a particular default wiring arrangement. Those additions are not universal properties of the bare IC.
If your design may grow from one button to several, decide whether the extra channels justify a larger board and different pinout now. Otherwise, the single-channel part is normally the simpler starting point.
Recommended Free Tools
TTP223 and TTP224 comparison
| Decision axis | TTP223 | TTP224 family | How to use the information |
|---|---|---|---|
| Touch keys | One key in Tontek’s Touch Series listing | Four keys for the cited TTP224C and TTP224B entries | Count the independent touch controls required by the product. |
| IC supply range | 2.0–5.5 V for the TTP223 entries in Tontek’s listing | 2.4–5.5 V for the cited TTP224C and TTP224B entries | Verify the exact suffix before connecting power. |
| Representative module supply range | 2.5–5.5 V on Sunrom’s cited one-channel board | 2–5.5 V on Sunrom’s cited four-channel board | These are supplier board specifications and do not replace the IC data for another board. |
| Output configuration on cited modules | Active-high or active-low; toggle or momentary options are described by Sunrom | Active-level and toggle/momentary options are described by Sunrom | Confirm the pads, jumpers and defaults on the exact module. |
| Representative PCB size | 15 × 11 mm on Sunrom’s cited TTP223 module | 35 × 29 mm on Sunrom’s cited TTP224 module | Use these only for those specific boards when planning enclosure space. |
The table separates manufacturer data for the IC from supplier data for particular modules. A different suffix or breakout can have a different operating range, pin arrangement or configuration method.
#1 Best Overall
- Read Before You Buy — No Video Output: These adapters support charging and USB 2.0 data transfer, but cannot transmit video signals. Except for standard USB webcams (which use USB data only), they are not compatible with HDMI/DisplayPort cables, video-capable USB-C hubs, or docking stations with video output.
- Convert USB-A Ports to USB-C: Designed to connect USB-C earphones, cables, flash drives, card readers, and other USB-C accessories to standard USB-A ports. Plug-and-play with no drivers or software required.
- Aluminum Alloy Housing: Built with a sturdy aluminum alloy shell that aids in heat dissipation and protects against daily wear and scratches. Designed to maintain a stable and secure connection.
- Compact & Travel-Friendly: The ultra-compact design allows the adapter to stay plugged into your device without blocking adjacent ports or adding bulk, reducing wear and tear on your original USB ports.
- 12-Month Warranty: Backed by a 12-month manufacturer warranty for peace of mind. Designed to meet strict quality control standards for reliable everyday performance.
What the part names actually tell you
TTP223 is a single-channel controller
Tontek’s series listing identifies TTP223 variants as one-key touch devices. A one-channel design keeps the wiring and firmware model small: one sensing electrode, one output to read and one touch state to interpret. That makes it suitable when the user interface has exactly one touch target or when you want a dedicated touch input alongside other controls.
TTP224 is a family label
TTP224 should not be treated as one complete specification. The cited official entries are TTP224C and TTP224B, and both are listed as four-key parts with a 2.4–5.5 V supply range. Other suffixes or boards may differ. Put the full part number on your bill of materials and retain the matching datasheet or module page in the build documentation.
A four-channel part is not four independent modules
One TTP224 board can expose four channels on a single PCB, but the board still needs a suitable electrode arrangement and enough connections to your controller. If the enclosure has only one touch location, the unused channels add no user-facing capability and may consume space you could avoid with a TTP223 board.
Do these 3 things before closing this tab:
1Clear out junk files and repair common Windows errors2Scan for outdated or missing drivers - takes under a minute3Repair Windows errors before they cause bigger problemsSupply voltage: check the exact layer you are buying
Voltage is the most important electrical qualification after channel count. Tontek lists 2.0–5.5 V for its TTP223 entries. For the cited TTP224C and TTP224B entries, Tontek lists 2.4–5.5 V. Those figures belong to the listed IC variants, not automatically to every breakout that carries a similar marking.
Rank #2
- 5-in-1 USB-C Hub: Experience comprehensive connectivity featuring a Power Delivery input, two USB-A 2.0 ports, a USB-A 3.0 port, and an HDMI port. (Note: The USB-C power delivery input port is only for connecting an external wall charger to power your laptop and cannot power peripheral devices.)
- 90W Pass-Through Charging: Achieve optimal charging with 90W pass-through power to your laptop, supported by a total input of 100W, with the hub reserving 10W for operational efficiency. (Note: Wall charger not included.)
- Quick Data Transfers: Accelerate your productivity with rapid data transfers using a high-speed 5Gbps USB 3.0 port and two 480Mbps USB 2.0 ports.
- 4K HDMI Display: Enhance your visual experience with a hub capable of delivering 4K resolution at 30Hz in both mirror and extend modes. Please note that this hub is compatible with MacBook (macOS 12 and newer), Windows 10 and 11, ChromeOS, and laptops equipped with DP Alt Mode and Power Delivery. Note: This device is not compatible with Linux.
- What You Get: Anker USB-C Hub (5-in-1, 4K HDMI), welcome guide, 18-month warranty, and our friendly customer service.
Sunrom’s representative TTP223 module is specified for 2.5–5.5 V, while its representative TTP224 module is specified for 2–5.5 V. A module supplier may include an LED, resistor network, connector or other board components that affect the board-level range or recommended connection. The lower limit on a board can therefore differ from the lower limit in an IC listing.
How to verify compatibility
- Write down the voltage available in the finished product, including its minimum and maximum under battery, USB or regulator conditions.
- Read the full IC suffix printed on the chip or listed by the seller.
- Read the module’s own operating-voltage statement if you are buying a breakout.
- Confirm that the controller input can safely accept the module’s output voltage and that all devices share a common ground.
- Do not infer a 5 V-only or 3.3 V-only requirement from the family name. Use the stated range for the exact part and board.
If the IC and module pages disagree, follow the board manufacturer’s connection guidance for that board and avoid assuming that the bare-IC figure authorizes every board configuration.
IC versus module: what changes on a breakout board?
The bare TTP223 or TTP224 IC is a component that must be placed on a designed PCB with an electrode, supply connections and whatever output conditioning your circuit requires. A module packages those pieces into a ready-to-wire board. Sunrom’s cited boards add a PCB, connections and configuration options, and describe their outputs as suitable for microcontroller inputs.
Because the board is a separate design, its dimensions, pin labels, indicator behavior and defaults belong to that board. Sunrom lists 15 × 11 mm for the cited TTP223 module and 35 × 29 mm for the cited TTP224 module. Those measurements are useful when checking enclosure clearance, but they are not universal dimensions for every TTP223 or TTP224 board.
Rank #3
- Sleek 7-in-1 USB-C Hub: Features an HDMI port, two USB-A 3.0 ports, and a USB-C data port, each providing 5Gbps transfer speeds. It also includes a USB-C PD input port for charging up to 100W and dual SD and TF card slots, all in a compact design.
- Flawless 4K@60Hz Video with HDMI: Delivers exceptional clarity and smoothness with its 4K@60Hz HDMI port, making it ideal for high-definition presentations and entertainment. (Note: Only the HDMI port supports video projection; the USB-C port is for data transfer only.)
- Double Up on Efficiency: The two USB-A 3.0 ports and a USB-C port support a fast 5Gbps data rate, significantly boosting your transfer speeds and improving productivity.
- Fast and Reliable 85W Charging: Offers high-capacity, speedy charging for laptops up to 85W, so you spend less time tethered to an outlet and more time being productive.
- What You Get: Anker USB-C Hub (7-in-1), welcome guide, 18-month warranty, and our friendly customer service.
What to identify on the board
- Power pins: Find the labels for supply and ground and verify polarity before applying power.
- Channel outputs: A TTP223 board normally exposes one output; a TTP224 board may expose one output for each touch channel. Count the actual labeled pins rather than relying on a product photograph.
- Configuration pads: Look for pads or jumpers that select active-high versus active-low and toggle versus momentary operation.
- Electrode area: Determine whether the board provides a touch pad or expects an external pad connected to the sensing input.
- Indicator LED: An LED can show state but may also affect current draw and visual behavior. Treat it as a board feature, not an IC guarantee.
Output modes and firmware consequences
The cited Sunrom TTP223 and TTP224 module pages describe selectable active-high or active-low output and toggle or momentary operation. In momentary mode, the output follows the touch action according to the board’s configured polarity. In toggle mode, a touch changes the output state and the next touch changes it again. The exact pad names, default state and selection procedure vary by board.
Active-high versus active-low
An active-high output is interpreted as asserted when it is at the higher logic level; an active-low output is asserted when it is low. Your firmware should define one symbolic state such as TOUCHED and map the physical level to it during initialization. This prevents a board swap from forcing changes throughout the application.
Momentary versus toggle
Use momentary mode when the application needs an event or a pressed/released state, such as a menu key or a hold-to-run control. Use toggle mode when the sensor itself should retain an on/off state, such as a simple lamp command. If your software already stores the state, momentary output usually leaves that state management in the controller; if the board toggles, avoid toggling the same command again in firmware unless that is intentional.
Step-by-step selection and wiring process
- List the touch targets. Count independent controls in the enclosure. One target points toward TTP223; multiple targets point toward a four-channel TTP224 variant such as the cited TTP224C or TTP224B.
- Choose the implementation level. Select a module for fast prototyping and accessible headers, or the bare IC when board size, electrode geometry and production assembly require your own PCB.
- Match the supply. Compare the product’s real supply range with the exact IC suffix and, separately, the module’s stated range.
- Plan the electrode. Place the touch area where a finger can reach it through the intended cover material, and keep the sensing area away from noisy or moving conductors as far as your mechanical design allows. Follow the IC or board layout guidance for the final PCB.
- Wire power first. Connect the board’s supply and ground to the controller’s corresponding rails while power is disconnected. Check polarity and continuity before switching on.
- Wire outputs. Connect the TTP223 output, or each selected TTP224 channel output, to controller input pins. Record whether each channel is active-high or active-low.
- Select the board mode. Set the documented pads or jumpers for momentary or toggle behavior and the required active level. Do this before writing assumptions into application code.
- Test one channel. Power the circuit, observe the board indicator if present, and read the input with a simple diagnostic program. Verify untouched and touched states before adding the remaining channels.
- Integrate the application. Add debounce or state-change filtering in firmware, then test rapid taps, long touches and release behavior in the complete enclosure.
Firmware practices that prevent false actions
Read each channel as a digital input and normalize its configured polarity in one place. For momentary operation, act on a stable edge or stable state instead of executing the command on every loop iteration while a finger remains on the pad. For toggle operation, decide whether the hardware or firmware owns the retained state; duplicating both can produce two changes for one touch.
Rank #4
- Dual Converters, Infinite Potential：Includes 2× USB C male to USB A female adapters and 2× USB A male to USB C female adapters. Perfect for a wide range of uses—tablets with Bluetooth keyboards, expand USB ports on macbook, and more. Two different converters for all your daily needs
- Next-Level 10Gbps & 3A Charging: No more slow 480Mbps, this usb to usb c adapter has a transfer speed of up to 10Gbps, allowing you to do more transferring in less time. This usb adapter fits both USB A and USB C charger, supporting up to 3A fast charging
- Upgraded Exquisite Craftsmanship: With an aluminum alloy housing and metal connector, the usbc to usb adapter is extremely durable and sturdy. Rigorously tested to withstand more than 10,000 times of plugging and unplugging, ensuring long-lasting performance
- Broad Compatible: The usb c to usb adapter widely supports all USB C/ USB A devices like laptops, tablets, cellphones, car chargers, and phone chargers. Such as compatible with MacBook Pro/Air 2023/2022, Thunderbolt 4/3 Devices,Apple MagSafe Watch 9/8/7/SE/Ultra, iPad Pro 2022/2021, Samsung Galaxy S23/S20/S10, and iPhone 17/16/15 Pro. Plug and play
- Please Note: To reach 10Gbps speed, keep the cable under 3.3 ft. For USB A Male to USB C adapters, try flipping the USB C connector. USB C Male to USB A adapters support bidirectional 10Gbps transfer within 3.3 ft
During bring-up, log the raw pin level and the interpreted touch state. This quickly exposes an inverted active level, a floating or miswired input, or a channel connected to the wrong controller pin. Once the mapping is proven, keep the channel-to-function map in a single table or constants section so a four-channel board can be rearranged without rewriting unrelated code.
Independent reader supportYour contribution helps us test, update, and keep practical guides available for everyone.Common mistakes and how to recover
Assuming every TTP224 has the same voltage range
Symptom: The design uses the 2.4–5.5 V figure from one TTP224 listing for a different board without checking its documentation. Fix: identify the suffix and use the board-level supply statement for the module you actually purchased.
Treating a module dimension as an IC dimension
Symptom: A board fits the prototype but not the final enclosure, or a production PCB is laid out around a supplier board’s outline. Fix: reserve the 15 × 11 mm and 35 × 29 mm figures only for the cited Sunrom boards; obtain the dimensions of your own board or design the footprint yourself.
The Tool Desk
Outbyte PC Repair FREERepair Windows errors before they cause bigger problemsFix Now →Outbyte Driver Updater FREEScan for outdated or missing drivers - takes under a minuteDriver Scan →Ignoring output polarity
Symptom: The controller reports a touch at idle or the command appears reversed. Fix: check the active-high/active-low selection, verify the untouched level with a meter or diagnostic printout, and invert the firmware interpretation if the board is configured the other way.
Best Value
- 5-in-1 Connectivity: Equipped with a 4K HDMI port, a 5 Gbps USB-C data port, two 5 Gbps USB-A ports, and a USB C 100W PD-IN port. Note: The USB C 100W PD-IN port supports only charging and does not support data transfer devices such as headphones or speakers.
- Powerful Pass-Through Charging: Supports up to 85W pass-through charging so you can power up your laptop while you use the hub. Note: Pass-through charging requires a charger (not included). Note: To achieve full power for iPad, we recommend using a 45W wall charger.
- Transfer Files in Seconds: Move files to and from your laptop at speeds of up to 5 Gbps via the USB-C and USB-A data ports. Note: The USB C 5Gbps Data port does not support video output.
- HD Display: Connect to the HDMI port to stream or mirror content to an external monitor in resolutions of up to 4K@30Hz. Note: The USB-C ports do not support video output.
- What You Get: Anker 332 USB-C Hub (5-in-1), welcome guide, our worry-free 18-month warranty, and friendly customer service.
Mixing toggle hardware with toggle software
Symptom: One touch appears to switch the function twice or leaves it in the opposite state. Fix: choose one owner for state retention and configure the board and firmware consistently.
Choosing four channels for a one-button product
Symptom: Unused inputs, a larger board and more wiring complicate an otherwise simple design. Fix: use the single-channel option unless expansion is a firm requirement.
Assuming a module’s pin labels are universal
Symptom: Power or output is connected to the wrong header position because a different board used another order. Fix: check the silkscreen and documentation for the exact PCB, and verify continuity before powering it.
Windows Errors? Fix Them Before They Spread
Repair common Windows errors and clear accumulated junk for a smoother, more stable PC - no reinstall needed.Free scan · no reinstallOutdated Drivers Are Slowing You Down
One free scan finds every outdated or missing driver and matches the right update for your exact hardware.Free scan · exact hardware matchWhich device fits common project types?
| Project requirement | More suitable starting point | Reason |
|---|---|---|
| One touch button on a compact prototype | TTP223 module | One channel and the cited 15 × 11 mm representative board keep wiring and board area small. |
| Four front-panel touch controls | TTP224-family module | The cited TTP224C and TTP224B parts provide four keys, and the representative board exposes four-channel functionality. |
| Custom production PCB with a single electrode | TTP223 bare IC or a verified TTP223 design | You control the electrode, connector and enclosure footprint instead of accepting a breakout outline. |
| Multi-key interface with a planned custom layout | Exact TTP224 suffix selected from its documentation | Channel count is appropriate, but layout and supply details must follow that specific variant. |
| Controller supply near the lower voltage limit | Whichever exact part and board explicitly cover it | The listed lower limits differ between TTP223, TTP224 variants and representative modules. |
Buying and design checklist
- Have you counted the required independent touch keys?
- Is the full IC suffix documented, rather than only the family name?
- Are the IC voltage range and module voltage range both confirmed?
- Do the board’s pin labels match your wiring diagram?
- Is the output active level known and represented correctly in firmware?
- Are momentary and toggle behavior deliberately selected?
- Does the actual PCB fit the enclosure and leave room for the touch electrodes?
- Will the controller have enough input pins for every channel?
- Have you tested the untouched level, a short tap, a long touch and release?
- Are unused channels handled according to the exact board documentation?
Final decision
For one independent touch control, start with TTP223. For several controls, start with the exact TTP224-family variant that provides the required channels; the cited TTP224C and TTP224B entries are four-key devices. Then verify the suffix-specific voltage range and the module’s own pinout, dimensions and configuration pads. That sequence—channel count first, electrical limits second, board details third—avoids the most common mismatch between a promising product listing and a working design.
Quick Recap
Product prices and availability are accurate as of the date/time indicated and are subject to change. Any price and availability information displayed on Amazon at the time of purchase will apply.
